About building and repair - the main page About building and repair - the main page About building and repair - the main page About building and repair - the main page

Pasting of walls and ceilings wall-paper (a part 2)

Pasting by wall-paper vnahlestku. Usually pasting by wall-paper begin from a wall with windows (from light) with transition in depth of a room that joints of panels were not visible.

All panels should be located on a wall vertically. For this purpose in each corner the first panel is pasted on the beaten off line, and by the others - in the area of an edge. For the first panel from a corner (luzga) measure the distance equal to width of the pasted panel, and by means of a plumb with a polished chalk a cord beat off a line on which it and will be pasted (fig. 101). Last panel on each wall paste not end-to-end to luzgu a corner, and blocking it on 20-30 mm. Therefore from a panel still to namazyvanija its gluing substance cut off surpluses. An edge blocking a corner, it is recommended to make an incision in several places that the panel was pasted as it is possible more densely, not forming waves and wrinkles.

101. Otbivka vertical lines by means of a plumb; 102. Paste drawing on wall-paper; and - on stolemaklovitsej, - on a floor mahovoj a brush On the following wall the first panel paste end-to-end to a corner, blocking the pasted tape or an edge wrapped on this wall. The edge in luzgah (corners) should be pasted more densely to walls that the corner was not rounded off. It is possible to block a corner and the whole panel provided that it is vertical, however thus all the same in luzgah the wrinkles spoiling a kind of pasting are often formed.

Before pasting a floor part close a paper and on it stack a pile wall-paper a face sheet downwards so that the edge of each underlaying panel acted from under overlying not less than on 10 mm. Stacked panels of wall-paper aspire to be curtailed into a roll. Therefore earlier prepared rolls it is recommended perekatat in the opposite direction. After that they lay down more exactly. Certainly, panels it is possible prigruzit on the ends any heavy subject. It is convenient also that at namazyvanii panels gluing substance they can move, and prigruzhennye remain on a place. That they did not move, one of the working holds panels with hands. It is more convenient to smear wall-paper on a table: it is necessary to bend down much less (fig. 102).

Namazyvanie carry out mahovoj a brush, flejtsem, maklovitsej or shoe or odezhnoj a brush along a panel without admissions, a thin equal layer. Especially well it is necessary to miss the mark edges which should soften then they will more densely lie down to edges before the pasted panel and it is better priklejutsja. Therefore at first it is recommended to miss the mark edges, then the panel rest, and in the end once again slightly to miss the mark edges. Many to put paste on the missed the mark edges does not follow, as at priglazhivanii from under them the gluing substance which that the corner was not rounded off is squeezed out.

It is possible to block a corner and the whole panel provided that it is vertical, however thus all the same in luzgah the wrinkles spoiling a kind of pasting are often formed.

Before pasting a floor part close a paper and on it stack a pile wall-paper a face sheet downwards so that the edge of each underlaying panel acted from under overlying not less than on 10 mm. Stacked panels of wall-paper aspire to be curtailed into a roll. Therefore earlier prepared rolls it is recommended perekatat in the opposite direction. After that they lay down more exactly. Certainly, panels it is possible prigruzit on the ends any heavy subject. It is convenient also that at namazyvanii panels gluing substance they can move, and prigruzhennye remain on a place. That they did not move, one of the working holds panels with hands. It is more convenient to smear wall-paper on a table: it is necessary to bend down much less (fig. 102).

Namazyvanie carry out mahovoj a brush, flejtsem, maklovitsej or shoe or odezhnoj a brush along a panel without admissions, a thin equal layer. Especially well it is necessary to miss the mark edges which should soften then they will more densely lie down to edges before the pasted panel and it is better priklejutsja. Therefore at first it is recommended to miss the mark edges, then the panel rest, and in the end once again slightly to miss the mark edges. Many to put paste on the missed the mark edges does not follow, as at priglazhivanii from under them the gluing substance which gets on a face sheet of wall-paper is squeezed out and spoils them. The squeezed out paste is necessary there and then for removing a pure rag.

Happens that the edges of wall-paper pasted on earlier laid panel, are badly pasted: or they were not softened, or the gluing structure was weak. In that case edges of the pasted panel at first grease by means of a small brush, and then paste a following panel, smoothing its rags or brushes which are more convenient (fig. 103).

103. Pasting of walls by wall-paper: folding of a panel of wall-paper, - panel gluing Sometimes after priglazhivanija under wall-paper remains air, and in such places they are blown up, forming air bubbles which should be pierced a pin or the sharp end of scissors, to squeeze out air and to smooth.

If the pasted panel was bent on all length and is inexact has laid down on an edge before pasted, having closed a drawing part at attempt it level on it folds can to be formed. Such panel is better for pasting "чр чръЁюхь" i.e. To block it a part of drawing before the pasted panel in the bottom part of a wall. It is possible to make an incision also it in several places that will allow to smooth wrinkles and to paste it precisely on an edge. Panels are bent from application of a bad paper for manufacturing of wall-paper or from non-uniform drawing of paste.

Pasting of difficult places. In some buildings on walls pass various pipes. They or densely adjoin to a wall, or partially are in it more thickly. It is desirable to paste over such pipes so that drawing coincided. A pipe preliminary clear of a dust and a dirt, olifjat and paint an oil paint. After its drying paste over with a paper in two layers that edges were pasted on both parties of a pipe to a wall for the width of 15-20 mm. Then a pipe paste over with wall-paper cut in the form of tapes. The panel not smeared with gluing structure put to the pasted over pipe, combine drawing, do labels and paste it (fig. 104).

104. Pipe pasting; 105. A marking of a place of the socket on a piece of wall-paper; 106. A scrap of wall-paper at plinths: and - sockets or switches are available scissors, - a knife If on walls and they for some reason or other cannot be removed, take a dry panel, combine it on drawing with earlier pasted, plan on it a socket or switch site, remove a panel, cut out the necessary aperture and paste, especially carefully smoothing nearby these devices (fig. 105). It is possible to make and so: on a pasted panel in the socket location to make a cut cross-wise, to smooth, and the ends to cut off a knife. At plinths wall-paper cuts off scissors or a knife (fig. 106).

border and frieze Gluing. Them paste in last turn and it is desirable on dried up wall-paper. That it was more convenient to work, they should be cut strips the in length of 1-2 m. If line earlier beaten off by a cord became hardly noticeable put new labels: by means of a ruler a simple pencil spend hardly appreciable lines on which the label is conducted.

In places priklejki a border or a frieze on wall-paper a small brush put gluing structure and allow to it to dry up. Then smear border or frieze strips, put them half-and-half, gluing structure inside, hang up on a shoulder and start a label: put a border or frieze strip to the put labels and cautiously smooth. Borders and friezes paste vnahlestku or end-to-end.

<< the previous page | to read further > >