About building and repair - the main page About building and repair - the main page About building and repair - the main page About building and repair - the main page

Technics of work as brushes,
Platens and vacuum cleaner (a part 2)

Work flejtsami and tortsovkami. Appointment of these operations - alignment svezhenanesennoj paints and removal of rough strips. From flejtsevanija the surface becomes smooth and equal, and from tortsevanija takes a form shagrenja (the rough surface consisting of smallest bugorkov).

Colouring by different brushes: and - a bench hammer, - flejtsem, in - tortsovkoj For this kind of works painting structure prepare for more dense, than at colouring without flejtsevanija and tortsevanija. This work is better for carrying out together: one paints, and another after it on a fresh paint flejtsuet or tortsuet.

Flejtsevanie (fig. 86. The right hand take flejts, left - a dry pure rag. With easy pressing spend on a surface flejtsem, comparing strips of the put paint. It is necessary to work without admissions. From work flejts becomes impregnated with a paint, therefore it needs to be wrung out, wiped regularly a dry rag and only after that to start to work. It is possible flejtsy to wash, and then to dry: wet flejtsy for work are unsuitable.

Tortsevanie (fig. 86. The Brush-tortsovku take in the right hand and carry out it tortsujushchie blows on the put paint. And, tortsovka should concern slightly only volosom paints. More than once to strike blows tortsovkoj to the same place it is not recommended: after paint drying such places will be allocated with a stain. In the course of work tortsovku periodically wipe a dry rag and if it is required - wash and dry.

Vytjagivanie of panels: and - on a ruler, - on a cliche Vytjagivanie of panels (fig. 87). The joint of two paints of different colour not always happens equal. To give to walls the beautiful and finished kind, a joint place often close a strip of a paint of other colour - a panel.

Panels from a glutinous paint carry out on the glutinous and mixed paints (the panel oil, and top glutinous). At oil colourings of a panel extend oil paints.

For vytjagivanija panels apply a usual glutinous paint, but more liquid consistence, it is recommended to dilute an oil paint with turpentine.

For work are necessary filenochnaja a brush and it is equal vystrugannaja a ruler or a cliche. A ruler strong press to beaten off namelennym a line cord. Moisten a brush in a paint, slightly wring out and, having put it to a ruler, with identical pressing spend an equal line of identical width - a panel. That the paint was not filled in under a ruler, its one edge chamfer (mow down). A ruler put a facet to a wall and on it the brush moves.

For vytjagivanija panels pour the Small amount of a paint in a jar, which krepjat on a lace at breast level.

Colouring by platens: and - nabiranie paints, - colouring Work as platens (fig. 88). The paint typed many, forms begin to flow, therefore platens wring out about a grid tense on a framework in the size 200x300 mm. Instead of a grid it is possible to take the same piece of a roofing steel or a tin and to punch in it frequent apertures. In capacity sheet put roughnesses downwards. It is possible to use also a piece of plywood or a thin board, nasverliv in them apertures in diameter of 12-15 mm located in chessboard order through 2-5 mm from each other.

The Design of platens does not give possibility to paint them of a surface of walls in corners, at platbands, plinths etc. Therefore such places should be painted preliminary a brush and it is good to shade.

The Platen paint so. Dip it into a paint, wring out its surpluses, spending it on a grid, bring to a surface and with pressing conduct it in the necessary direction.

The Paint is necessary for shading carefully, for what the platen prokatyvajut some times in the same place: on walls usually at first from top to down, then from below upwards etc., imposing paint strips one on another so that they were blocked on 4-5 mm. In process of an expenditure of a paint force of pressing the platen increases.

The First coat is recommended to be applied the same colour, as koler. To carry out colouring it is possible for one or for two times. For example, at first colouring conduct in a horizontal direction, and then in the vertical. It is necessary to watch that does not remain potekov.

The surfaces Painted by the platen look like the furnish executed under large shagreen leather.

Prior to the beginning of colouring it is necessary to make trial colouring of any surface: walls, plywood or cardboard sheet to get some skill. For one day it is possible to paint about 300 m 2 surfaces at high quality of work. And one platen it is possible to paint more than 3 thousand in m 2 surfaces.

Colouring by means of a vacuum cleaner. By means of a spray it is possible to put glutinous and limy structures a thin and equal layer.

It is possible to Paint on a first coat or an old paint coat or on the fresh paint put by a brush, for the purpose of its alignment.

The Painting structure should be filtered through a fine sieve or a gauze. To bank fill with a paint no more than on 3/4 its volumes. On bank it is recommended to moisten a rubber ring with water that raises its density prileganija to bank.

Working as a spray, it is important to pick up optimum length of a stream of a sprayed paint which should be within 40-70 more often see At longer strue paint particles do not reach a surface.

To Paint ceilings follows from a table, a chair etc., holding a spray on identical distance from a surface, moving its smooth krugoobraznymi movements, without detaining long on one place not to oversaturate a surface a paint in avoidance potekov. Occurrence of a glossy shade instead of the matte specifies in a limit of saturation of a surface a paint. It is especially visible when colouring conduct against light (against a window).

<< the previous page